1 When using the GUI interface to configure the Cisco 1200 Series AP for Hot Standby, what is the role of the monitored AP?
Access Point Root (No Fallback)
Access Point Root (Fallback to Repeater)
Access Point Root (Fallback to Radio Shutdown)
Access Point Root (Fallback to Radio Island)
2 What are ways to return a Cisco AP to its factory default settings? (Select two.)
Power cycle the AP while holding in the mode button.
Issue the reset command from the privileged mode CLI prompt.
Click the Reset to Defaults button on the System Configuration screen.
Issue the erase running-config command followed by reload from the privileged mode CLI prompt.
3 Which of the following commands are used to set the AP output power to 20 mW and the data rate to 11 Mbps only? (Select two.)
AP(config-if)# power 20
AP(config-if)# power local 20
AP(config-if)# power client 20
AP(config-if)# speed 11.0
AP(config-if)# speed basic-11.0
AP(config-if)# speed basic-11.0 1.0 2.0 5.5
4 Which of the following are true when setting the IP address and SSID of the AP? (Select three.)
The SSID can be assigned without setting the IP address.
The IPSU can be used to assign the SSID.
The PC used to set up the SSID and IP address must have an IP address of its own.
The IPSU can be used to change the IP address again, but only if the access point is reset to default values.
The IPSU can only be used to change the SSID for the 5GHz radio when an access point is operating in dual-mode.
5 When configuring the AP Radio Port Hardware setup page, which settings are recommended in situations where communication is poor and many client devices are associating with the access point?
low fragment threshold and high RTS threshold
high fragment threshold and high RTS threshold
high fragment threshold and low RTS threshold
low fragment threshold and low RTS threshold
6 Which command is used to set the parent AP for a repeater AP?
AP(config)# parent 10.0.0.1
AP(config-if)# parent 1 10.0.0.1
AP(config-if)# parent 1 abcd.1234.ab12
AP(config)# parent abcd.1234.ab12
7 On the Cisco AP 1200 series, what is the name of the 802.11a radio interface?
interface dot11radio 0
interface dot11radio 1
interface dot11radio a
interface 802.11a radio
8 What are valid methods of configuring an AP? (Select three.)
web browser
DNS server
console port
auxiliary port
Telnet session
9 When configuring the access point, which Ethernet page contains information about the operational status of the Ethernet port?
Ethernet Port
Ethernet Identification
Ethernet Hardware
Ethernet Filters
Ethernet Advanced
10 Which CLI command lists information about Cisco APs located in the same Layer 2 domain as the current AP?
AP# show dot11 adjacent-ap
AP# show dot11 network-map
AP(config)# dot11 network-map 30
AP# show dot11 associations statistics
AP# show dot11 associations
11 What does a blinking amber status LED indicate in a 1200 series access point?
no client devices associated
no power
transmitting or receiving radio packets
general warning
12 What is needed by the Cisco IP Setup Utility (IPSU) to learn the current IP address of an access point?
SSID of the AP
MAC address of the AP
system name of the AP
domain name of the AP
13 What is important information that should be gathered before setting up an access point? (Select three.)
system name
service set identifier
maximum number of wireless clients
SNMP community name
MAC address from the PC used to configure the access point
14 While configuring an interface on a Cisco 1200 series AP, the system administrator attempts to use the keystroke Ctrl+E to move the cursor to the end of the line without success. Why is the command not working?
This command only works in router IOS and not AP IOS.
The command to move the cursor to the end of the line is ESC E not Ctrl+E.
Advanced editing features on the AP have been disabled.
This command is only active in global config mode not interface config mode.
15 How does an AP behave when the receive antenna is set to diversity?
It will use the antenna that receives the best signal.
It will use both antennas at the same time.
It will round-robin between the two antennas.
The AP will always use one antenna to transmit and the other to receive.
16 In the Management System Setup Page, which AP Radio pages are available for configuration? (Select four.)
Radio Port Link
Radio Identification
Radio Hardware
Radio Testing
Radio Advanced
Radio Security
17 What must be enabled to use load balancing and TKIP on a Cisco AP?
Advanced AP Features
Cisco Aironet 802.11 Extensions
WAP
Data Beaconing
Public Secure Data Forwarding
18 An IP address needs to be set on a Cisco 1200 series AP. Which interface should be associated with the IP address?
dot11 radio interface
ethernet interface
bridge virtual interface
It does not matter
19 What is the default IP address of a Cisco 1200 series AP?
10.0.0.1
127.0.0.1
172.27.20.1
192.168.2.1
20 Which of the following are true about the SSID (Select two.)?
The SSID is always a 32-bit long alphanumeric string.
The SSID is case sensitive.
The SSID is, by default, sent out as a beacon on the WLAN.
The SSID is an effective method of WLAN security.
21 Using the CLI, which global configuration mode command enables CDP on a Cisco AP?
cdp protocol enable
cdp enable
cdp run
cdp start
22 What is the result of the command sequence illustrated? (Select two.)
The SSID for the 2.4 Ghz radio is changed to frey.
The SSID for the 5 Ghz radio is changed to frey.
The SSID for both the 2.4 Ghz and the 5 Ghz radio is changed to frey.
The privilege level required to set the maximum number of associations is set to 15.
The maximum number of associations to the SSID is set to 15.
Nothing will happen until the AP is rebooted.
23 What is the default enable password for a Cisco 1200 series AP?
Cisco
Tsunami
Aironet
Wireless
There is no default enable password.
Class
24 In the displayed serial port settings properties, which of the settings are correct to enable a communications session to be established with a Cisco 1200 series AP? (Select three.)
Bits per second
Data bits
Parity
Stop bits
Flow control
25 Which Cisco access point is shown in the graphic?
Cisco Aironet 1100
Cisco Aironet 1200
Cisco Aironet 1300
Cisco Aironet 1350
26 Which command will erase the configuration files stored in NVRAM? (Select two.)
ap# erase configuration
ap# erase startup-config
ap# erase running-config
ap# erase flash
ap# erase start
ap# erase run
27 When configuring an AP through the IOS CLI, which keystroke recalls the most recent entry in the command buffer and pastes it into the command line?
Esc-Y
Ctrl-Y
Tab
Ctrl-H
Esc-P
6 days ago